Wow hey everyone so today I’m going to
be showing you a really cool 3d print
that will allow you to charge your
electronics with a fallout 4 fusion core
[Music]
we’re going to be messing around with
some different liquids that you mix in a
two to one ratio and it allows you to
clean up the voids so you see how
there’s different lines that are built
into the 3d printing process so what
we’re going to do is clean it up and
then we’re going to spray paint this
close up those surfaces are nice and
smooth now and it creates a barrier in
between the paints this one is a any
surface so it’ll work on plastic and
everything this however is not so I’m
hoping that layer that I’ve applied make
it nice and smooth will also protect the
ABS plastic
[Music]
[Music]
so here you can see the two models I am
definitely not an artist and it’s been a
long time since arts and crafts so I did
my best with this and there’s a couple
other details that I could have probably
added like these are supposed to be dark
and also the little lines here on the
side but as I start practicing more and
more with painting and my confidence
builds I’m going to basically do a lot
more of the details but after kind of
botching a couple of these little
circles here I was like oh maybe it
would have been better off if I would
have painted it at all so let me know
what you guys think I do have to try and
learn so this is all process that you
guys get to just see me fail and make my
strides so it’s kind of interesting for
the both of us what’s going to happen
you charge it via microUSB and then you
can plug in any USB device you want here
you can see my phone that’s on three
percent so I’m gonna go ahead and press
the button there it goes on whenever the
green button goes and instantaneously
goes to seven percent that’s impossible
this literally is a fusion core so I’m
going to go ahead and install this
inside of the fusion course you can get
a better look of what its going to
actually be in the end
press the button while it’s green that’s
when you put and there you go
this is pretty freakin sweet now that
I’m working with boxy and TechShop
there’s a lot of possibilities and it’s
going to be awesome so I’m really
excited this is pretty cool so we’ll see
what else we can print so thank you so
much for watching and as always take it
easy
[Music]
[Music]
you
be showing you a really cool 3d print
that will allow you to charge your
electronics with a fallout 4 fusion core
[Music]
we’re going to be messing around with
some different liquids that you mix in a
two to one ratio and it allows you to
clean up the voids so you see how
there’s different lines that are built
into the 3d printing process so what
we’re going to do is clean it up and
then we’re going to spray paint this
close up those surfaces are nice and
smooth now and it creates a barrier in
between the paints this one is a any
surface so it’ll work on plastic and
everything this however is not so I’m
hoping that layer that I’ve applied make
it nice and smooth will also protect the
ABS plastic
[Music]
[Music]
so here you can see the two models I am
definitely not an artist and it’s been a
long time since arts and crafts so I did
my best with this and there’s a couple
other details that I could have probably
added like these are supposed to be dark
and also the little lines here on the
side but as I start practicing more and
more with painting and my confidence
builds I’m going to basically do a lot
more of the details but after kind of
botching a couple of these little
circles here I was like oh maybe it
would have been better off if I would
have painted it at all so let me know
what you guys think I do have to try and
learn so this is all process that you
guys get to just see me fail and make my
strides so it’s kind of interesting for
the both of us what’s going to happen
you charge it via microUSB and then you
can plug in any USB device you want here
you can see my phone that’s on three
percent so I’m gonna go ahead and press
the button there it goes on whenever the
green button goes and instantaneously
goes to seven percent that’s impossible
this literally is a fusion core so I’m
going to go ahead and install this
inside of the fusion course you can get
a better look of what its going to
actually be in the end
press the button while it’s green that’s
when you put and there you go
this is pretty freakin sweet now that
I’m working with boxy and TechShop
there’s a lot of possibilities and it’s
going to be awesome so I’m really
excited this is pretty cool so we’ll see
what else we can print so thank you so
much for watching and as always take it
easy
[Music]
[Music]
you
Please follow and like us:
Be First to Comment