hey guys here’s my mini flamethrower
later
I used a Ronson Comet lighter I’ll leave
a link in the description for some of
the parts some brass tubing superglue
butane fuel as the propellant the top of
a pop rivet which I’ll show you where
that goes in a sec and then the cig
nighter and this will act as your pilot
torch for lighting your fuel I also have
a review of this so actually when you
buy this make sure you pick up a few
they’re really cheap prob about a buck
apiece depending on what what site you
use but they’re not that reliable so if
you don’t you know I feel only by one
cut it usually takes a couple weeks to
get in the mail so pick up like you know
three or four just in case you don’t
waste your time so basically I have the
Ronson covered in duct tape just for the
added look and then modify the cig
nighter by cutting off the top
you didn’t actually need all that bulk
it’s actually just like tubing so I used
Dremel bit and if you guys haven’t
already seen it check out my mod guide
for how to modify your lighters it
doesn’t have to be a Ronson it just has
to be a refillable butane lighter and
the way you know if it’s refillable
you’ll see this little valve it’s a
metal valve and that means you can
refill it using any type of butane fuel
so that’s pretty much how you can tell
so this is just a support beam it
doesn’t really have any other purpose
other than support I just use some brass
tubing and then put this down the barrel
I cut off the top and all you have is
this little nail head and that was just
just to clean it up doesn’t really have
to be there unless you’re picky and want
it to look a little bit nicer and then I
just used some superglue to keep that in
and also a little bit of support on the
side
for the sig nighter which is a little
cigarette lighter I showed you it’s
pretty cool actually I’ll show you how
it works so basically how it is it
doesn’t have very much fuel but it’ll is
also refillable and adjustable so it’s
kind of nice so I’ll show you guys real
quick how it works okay
so here it is try and get the majority
of out the range sometimes this thing is
a pain yeah there we go which I never
more reliable lighter but I’m just going
to use this there we go
I don’t know why it’s not working right
now so that’s pretty much it
a pretty decent flame that was about
maybe two and a half three from where I
was shooting it and I’m not I think it’s
pretty cool wouldn’t really expect it
packs pretty pretty good punch size
matters not but let me know if you guys
liked what I did and leave a comment in
the description of any other types of
letters that you want me to try I can
basically put any fuel I have a pepper
spray lighter a skunk lure lighter so
you can spray someone with this really
stinky skunk scent and I’ll leave links
to those in the description as well so
please subscribe if you like what you
see thanks for watching
later
I used a Ronson Comet lighter I’ll leave
a link in the description for some of
the parts some brass tubing superglue
butane fuel as the propellant the top of
a pop rivet which I’ll show you where
that goes in a sec and then the cig
nighter and this will act as your pilot
torch for lighting your fuel I also have
a review of this so actually when you
buy this make sure you pick up a few
they’re really cheap prob about a buck
apiece depending on what what site you
use but they’re not that reliable so if
you don’t you know I feel only by one
cut it usually takes a couple weeks to
get in the mail so pick up like you know
three or four just in case you don’t
waste your time so basically I have the
Ronson covered in duct tape just for the
added look and then modify the cig
nighter by cutting off the top
you didn’t actually need all that bulk
it’s actually just like tubing so I used
Dremel bit and if you guys haven’t
already seen it check out my mod guide
for how to modify your lighters it
doesn’t have to be a Ronson it just has
to be a refillable butane lighter and
the way you know if it’s refillable
you’ll see this little valve it’s a
metal valve and that means you can
refill it using any type of butane fuel
so that’s pretty much how you can tell
so this is just a support beam it
doesn’t really have any other purpose
other than support I just use some brass
tubing and then put this down the barrel
I cut off the top and all you have is
this little nail head and that was just
just to clean it up doesn’t really have
to be there unless you’re picky and want
it to look a little bit nicer and then I
just used some superglue to keep that in
and also a little bit of support on the
side
for the sig nighter which is a little
cigarette lighter I showed you it’s
pretty cool actually I’ll show you how
it works so basically how it is it
doesn’t have very much fuel but it’ll is
also refillable and adjustable so it’s
kind of nice so I’ll show you guys real
quick how it works okay
so here it is try and get the majority
of out the range sometimes this thing is
a pain yeah there we go which I never
more reliable lighter but I’m just going
to use this there we go
I don’t know why it’s not working right
now so that’s pretty much it
a pretty decent flame that was about
maybe two and a half three from where I
was shooting it and I’m not I think it’s
pretty cool wouldn’t really expect it
packs pretty pretty good punch size
matters not but let me know if you guys
liked what I did and leave a comment in
the description of any other types of
letters that you want me to try I can
basically put any fuel I have a pepper
spray lighter a skunk lure lighter so
you can spray someone with this really
stinky skunk scent and I’ll leave links
to those in the description as well so
please subscribe if you like what you
see thanks for watching
Please follow and like us:
Be First to Comment