Press "Enter" to skip to content

This ONE TOOL Has Everything You Need To SURVIVE


today we’re going to be showing you how
to take some PVC some rubber tubing and
a toilet brush to make an arrow launcher
that also doubles as a survival kit full
of first aid water purification and fire
starting materials this one tool could
be everything you need to stay alive in
to start out there’s a whole bunch of
PVC pieces we need as well as this
toilet brush and some rubber tubing
we’re just going to start building and
showing you the pieces that were using
along the way the basic idea is that
we’ll take these PVC pipes fittings the
toilet brush and the rubber tubing fit
them all together and turn them into
sort of a slingshot for arrows the empty
pieces of pipe will be used as storage
containers for other survival pieces
we’re gonna start with a piece of this
one-inch PVC the idea is that we’ll have
a fork coming up on the top and then a
couple other pieces that reach back with
a bridge in between them as a guard and
sort of a rest that goes in your forearm
so as you pull back on the arrow
you’re not just twisting your wrist the
handle all right on the bottom of the
handle we’re gonna take this 1 inch male
adapter this is for switching from slip
pieces the threaded pieces
Popat right on the bottom some of our
PVC cement to attach it you’ll be able
to put a cap onto here just threading
that on for now we’ll leave that off
moving on to the next piece all right
we’ve got a key we’re just gonna put
this right on the top of our handle
now I’ve got this sort of weird piece
it’s a three quarter by three quarter by
one half inch piece three quarter inch
pipes fit into these two sliding and
then there’s a one half inch threaded
portion right here what’s interesting is
that if this piece of pipe didn’t have
markings and ridges on the side it would
fit pretty much perfectly into this tee
so what we’re actually to do is we’re
gonna shave these down so we can just
glue this piece directly into the RT oh
yeah that file it down piling took about
15 seconds and now this just fits in
beautifully a little bit of resistance
but not too much what we need to do is
make sure that both of the smaller ends
of these pipes are facing the same
direction because we’re gonna have our
fork come up here and then this is where
our support is gonna run out and that’ll
go along our arm don’t think we want
them perfectly straight up and down we
are going to want just a little bit of a
tilt so of course we’re gonna take these
out we’ll add glue and then when we
twist them into place I’ll make sure
that we’ve got just a little bit of
slant beautiful we now want to attach
two of these three quarter inch male
adapters onto the top of our fork
however these don’t just fit right on so
what we actually need is a piece of 3/4
inch PVC as a joiner in between
[Music]
now not only do we have two more spots
with caps that screw on and off but
below the caps we’ve got a pretty good
spot where we can attach things onto the
side and this is where the cord is going
to go the elastic rubber cord that we
use to draw back and fire our arrow
we’ve now got two of these half inch
male adapters we’re gonna thread those
in onto both sides here and this is
where our pipes can extend from well
water support to reach almost to the
elbow but we’re not just gonna have the
pipe go straight here we’re gonna have
to add a tee piece and then ends on to
the extensions as well so we’ll go a
little bit shorter than the full length
we want to go cut off a couple pieces
that long this is about nine inches long
kind of depends on the size of your arms
before we submit this in let’s build the
rest of the support that’s going to go
on to it just so we make sure we’ve got
all the right sizing and everything have
a tee another tee and these will both
angle up because in between them we’re
gonna have this 45-degree angle piece
that’s the basic shape of the support so
it will hold it on our arm that 45
degree angle piece will do a great job
of just letting us have a resting spot
or just connect that all with some more
half-inch pipe
those will connect to our tea pieces I
think at this point we can now glue
these into place and then glue this on
the back we’re gonna add pretty much the
same thing we’ve put on the other three
we’re gonna use some more of these mail
adaptors fit them on and then they’ll
have caps that go on top of them once
again we just need some short pieces of
our half-inch pipe to act as a connector
in between at this point our frame is
built and so it’s time to move on to
adding the other components we’re going
to be using this toilet brush to make
something of a DIY whisker biscuit
that’s something that just has little
hairs or fibers all pointing to one spot
in the middle an arrow can rest in it
and the fletchings can pass right
through because it’s not too dense of
bristles
we’ve got more brush than we need here
start by just trimming it off to try and
bend this a little bit more close so we
don’t need anything higher than right
about here in fact the arrow will rest
in the little Bend part and it doesn’t
really need to go much above that try
and trim it just a little bit there we
are still losing bristles quite a lot
and that’s because the bristles are held
in by wires twisted together so the stop
those from falling out we’re gonna try
and twist the wires together more if
then we’re gonna get some epoxy and just
cover up on top of the wires just to
keep those all in place what I’m using
is some quick-set jb weld there’s lots
of other options that would work just as
well
while the epoxy is curing we’re just
going to do a little bit of decoration
and that in this case means spray paint
we’re just going to turn this whole
thing black and maybe paint the caps a
[Music]
let’s see what we can do about attaching
her bristles right here in the middle
we’re gonna be using four that is just
some wire we’re gonna wrap it around the
top of our bristles and then we’re gonna
wrap it around the bottom of this
threaded portion just try and hold it
still
you might also wrap a little bit more
wire around the very bottom of it and
then around this t-shaped piece just to
hold it still so it’s not moving back
and forth next step is to attach the
launching mechanism itself which is
going to be made out of this rubber
tubing we’re gonna have it attached on
the top of both sides of the fork reach
to the back and then we’ll actually have
it in two separate pieces connecting the
two will be a piece of paracord which
should be thin enough for the nock of
the arrow to fit
[Music]
both our rubber cords are almost
reaching to the bridge maybe half an
inch three quarters of an inch short now
we need to join these together with a
piece of paracord we use a piece maybe
five inches long it’s not extremely
important that you have it exactly the
right length because any extra will just
stay inside the surgical tubing before
we cut off our length of surgical tubing
we’re gonna tie a knot in two different
spots we want this to be a very tight
knot pull it as tight as you can get one
knot right there and the second knot
maybe three or four inches away from the
first one now we need to fit the knots
inside the surgical tubing about half an
inch down take some squeezing and
stretching to make sure our little
pieces of knotted paracord stay in place
we’ll tighten them on with two more
small zip ties
[Music]
at this point the main body build is
complete and if we want we can start
using it right now in fact let’s give it
a couple test shots
hah look at that I’m usually a terrible
shot I was living my second try first
shot second shot man now I don’t want to
do any more because I’m sure there won’t
be as good there are other modifications
that we can make for example if you find
it hard to grip onto the arrow we can
take a little bit of duct tape and we
can make a pull-tab some people might
find that easier to hold on to than the
nock itself not only can we use this for
shooting arrows and hunting but since
it’s all hollow we’ve got lots of
clothes
caps waterproof storage containers and
we can fit a surprising amount inside of
this thing let’s take some wind proof
matches it’s gonna be using duct tape to
make smaller bags because lots of things
come in plastic pouches where we can
make plastic pouches out of ziplock bags
we just want them to be a little more
pretty good burn time immune to the wind
great thing to have several of these are
iodine tablets that are used for
decontaminating water you add a couple
of these tablets to one liter of water
and then you wait about five minutes and
it will actually kill pretty much
anything in there that you don’t want
and you can fit quite a few of these
into a very small space just to make it
a little bit easier to draw these back
out I’m gonna add a little wire handle
this can then drop down in but it’s easy
to pull right back out it’s got some
antibiotic ointment and some bandages if
you don’t like the idea of using tape to
hold your containers together you can
also try the hot wire method that we’ve
shown you previously to sort of melt the
bags into a custom shape
I do like in this situation the idea of
using tape it is a little bit stronger
and in an emergency you can probably use
there’s a little spherical compass
instrument fit into our lid small enough
just pop that on we’ve got wind proof
matches we’ve got bandages we’ve got
antibiotic ointment we’ve got a compass
oh we got the emergency water tablets
that’ll help keep us from getting
infections and cuts and scrapes
everywhere
won’t be exposed we’ll be able to start
fires we’ll be able to clean water
sometimes we’re going to want to hunt
with the bow and sometimes we’re gonna
want something else just give ourselves
the opportunity to get fish nice they
really don’t take up a lot of space so
you can fit them down even the small
little crevices give ourselves a little
bit of extra fishing line fish hooks
[Music]
you can fit a ton of fishing line around
a small devil like this here we’ve got a
saw it’s just a bunch of wires with even
thinner wires wrapped around them so you
wrap this around the log and just pull
it back and forth you start cutting
through wood you’re just going to wrap
this around top of the fort see bits of
webbing or the handles that you hold
onto anyone’s gonna tie those you saw
attached nice and out-of-the-way two
more things are gonna add some paracord
that we’re just gonna wrap around the
handle and some duct tape that we’re
just gonna wrap around one of the side
supports our survival bow has now been
filled to the brim with all sorts of
stuff to keep us alive
it’s got paracord it’s got duct tape
it’s got water purification tablets we
have a saw to cut wood we’ve got matches
to light wood on fire we can hunt we can
fish with the hooks and the reel that
we’ve got in there we’ve got a compass
we’ve got some basic first-aid this
thing has got a lot of good stuff packed
into it and maybe most importantly it’s
really fun to shoot my aim is terrible
but my consistency that was amazing I
almost robhinhood at that we want to
offer a special thank you shout out to
Daniel Meade for sharing the design of
your survival sling bow with us thanks
for watching today guys don’t forget
that that box up at the top will take
you directly to our last video because
the fun doesn’t have to end now the box
at the bottom will show you what YouTube
thinks you should be watching next and
there’s balm in the middle will
subscribe you to the channel that way
you never miss out on the fun don’t
forget to ring that Bell and we will see
in the next one talk to you then [Music]
Please follow and like us: